Configure IPSec VPN Tunnels (Site-to-Site) (2024)

Configure IPSec VPN Tunnels (Site-to-Site)

Updated on

Apr 4, 2024

Focus

Download PDF

Updated on

Apr 4, 2024

Focus

  1. Home
  2. Network Security
  3. Configure IPSec VPN Tunnels (Site-to-Site)

Download PDF

Network Security

Table of Contents

Learn how to configure a site-to-site IPSec VPN tunnel.

Where Can I Use This?

What Do I Need?

  • Prisma Access

  • PAN-OS

No license required

To set up site-to-site VPN:

  • Make sure that your Ethernet interfaces, virtual routers, and zones are configured properly. For more information, see Configure Interfaces and Zones.

  • Create your tunnel interfaces. Ideally, put the tunnel interfaces in a separate zone, so that tunneled traffic can use different policy rules.

  • Set up static routes or assign routing protocols to redirect traffic to the VPN tunnels. To support dynamic routing (OSPF, BGP, RIP are supported), you must assign an IP address to the tunnel interface.

  • Define IKE gateways for establishing communication between the peers across each end of the VPN tunnel; also define the cryptographic profile that specifies the protocols and algorithms for identification, authentication, and encryption to be used for setting up VPN tunnels in IKEv1 Phase 1. See Set Up an IKE Gateway and Define IKE Crypto Profiles.

  • Configure the parameters that are needed to establish the IPSec connection for transfer of data across the VPN tunnel; See Set Up an IPSec Tunnel. For IKEv1 Phase-2, see Define IPSec Crypto Profiles.

  • (

    Optional

    ) Specify how the firewall will monitor the IPSec tunnels. See Monitor Your IPSec VPN Tunnel .

  • Define Security policies to filter and inspect the traffic.

    If there’s a deny rule at the end of the security rulebase, intrazone traffic is blocked unless otherwise allowed. Rules to allow IKE and IPSec applications must be explicitly included above the deny rule.

    If your VPN traffic is passing through (not originating or terminating on) a PA-7000 Series or PA-5200 Series firewall, configure a bidirectional Security policy rule to allow the ESP or AH traffic in both directions.

When these tasks are complete, the tunnel is ready for use. Traffic destined for the zones/addresses defined in a policy rule is automatically routed properly based on the destination route in the routing table, and handled as VPN traffic. For a few examples on site-to-site VPN, see Site-to-Site VPN .

"); adBlockNotification.append($( "Thanks for visiting https://docs.paloaltonetworks.com. To improve your experience when accessing content across our site, please add the domain to the allow list on your ad blocker application." )); let adBlockNotificationClose = $("x"); adBlockNotification.prepend(adBlockNotificationClose) $('body').append(adBlockNotification); setTimeout(function (e) { adBlockNotification.addClass('open'); }, 10); adBlockNotificationClose.on('click', function (e) { adBlockNotification.removeClass('open'); }) } }, 5000)

Previous Proxy ID for IPSec VPN
Next Set Up an IKE Gateway

Recommended For You

{{ if(( raw.pantechdoctype != "techdocsAuthoredContentPage" && raw.objecttype != "Knowledge" && raw.pancommonsourcename != "TD pan.dev Docs")) { }} {{ if (raw.panbooktype) { }} {{ if (raw.panbooktype.indexOf('PANW Yellow Theme') != -1){ }}

{{ } else if (raw.panbooktype.indexOf('PANW Green Theme') != -1){ }}

{{ } else if (raw.panbooktype.indexOf('PANW Blue Theme') != -1){ }}

{{ } else { }}

{{ } }} {{ } else { }}

{{ } }} {{ } else { }} {{ if (raw.pantechdoctype == "pdf"){ }}

{{ } else if (raw.objecttype == "Knowledge") { }}

{{ } else if (raw.pancommonsourcename == "TD pan.dev Docs") { }}

{{ } else if (raw.pancommonsourcename == "LIVEcommunity Public") { }}

{{ } else { }}

{{ } }} {{ } }}

{{ if (raw.pancommonsourcename == "LIVEcommunity Public") { }}

{{ if (raw.pantechdoctype == "pdf"){ }}

{{ } }}

{{ } else { }}

{{ if (raw.pantechdoctype == "pdf"){ }}

{{ } }}

{{ } }}

{{ if (raw.pancommonsourcename != "TD pan.dev Docs"){ }} {{ if (raw.pandevdocsosversion){ }} {{ } else { }} {{ if ((_.size(raw.panosversion)>0) && !(_.isNull(raw.panconversationid )) && (!(_.isEmpty(raw.panconversationid ))) && !(_.isNull(raw.otherversions ))) { }} (See other versions) {{ } }} {{ } }} {{ } }}

{{ } }}{{ if (raw.pantechdoctype == "bookDetailPage"){ }}

{{ } }}{{ if (raw.pantechdoctype == "bookLandingPage"){ }}

{{ } }}{{ if (raw.pantechdoctype == "productLanding"){ }}

{{ } }}{{ if (raw.pantechdoctype == "techdocsAuthoredContentPage"){ }}

{{ } }}{{ if (raw.pantechdoctype == "pdf"){ }}

{{ } }}

© 2024 Palo Alto Networks, Inc. All rights reserved.

Configure IPSec VPN Tunnels (Site-to-Site) (2024)

FAQs

How to configure IPsec site-to-site VPN? ›

Let us examine each of the above steps.
  1. Step 1: Creating Extended ACL. Next step is to create an access-list and define the traffic we would like the router to pass through the VPN tunnel. ...
  2. Step 2: Create IPSec Transform (ISAKMP Phase 2 policy) ...
  3. Step 3: Create Crypto Map. ...
  4. Step 4: Apply Crypto Map To The Public Interface.

Which solution allows you to create a site-to-site VPN tunnel? ›

Site-to-site VPN Protocols

IPsec is often used in tandem with other protocols such as L2TP (Layer 2 Tunneling Protocol) to provide encryption, secure communication between networks. GRE (Generic Routing Encapsulation) is sometimes used with IPsec for creating tunnels, although GRE by itself does not provide encryption.

What is the difference between IPsec tunnel and site-to-site VPN? ›

IPsec VPN securely interconnects entire networks (site-to-site VPN) OR remote users with a particular protected area such as a local network, application, or the cloud. SSL VPN creates a secure tunnel from the host's web browser to a particular application.

How to configure PfSense site-to-site IPsec VPN tunnel for remote access? ›

Creating a Site-to-Site tunnel on the PfSense device
  1. Go to VPN -> IPsec.
  2. Select +Add P1. Key Exchange Version: IKEv2 if the Firewall version supports it, IKEv1 otherwise. Internet Protocol: IPv4. Interface: <Your pfSense WAN Interface> Remote Gateway: P81 Gateway IP address. Authentication Method: Mutual PSK.

What is an IPsec VPN tunnel? ›

An IPSec VPN is a VPN software that uses the IPSec protocol to create encrypted tunnels on the internet. It provides end-to-end encryption, which means data is scrambled at the computer and unscrambled at the receiving server.

What is the difference between site-to-site and tunnel interface? ›

A site-to-site VPN does not give you that type of redundancy since the network is configured in the policy itself. Tunnel interface offloads that configuration from source network to destination network to a route policy.

What is the best option for site-to-site VPN? ›

IPsec is well-suited for site-to-site VPNs because it can handle the secure interconnection of different physical locations or networks, making it a preferred choice for organizations that need to establish secure connections between their branch offices, data centers, or remote sites.

Which are the two main types of VPN tunnels? ›

The two main types of VPN tunnels for businesses are remote access and site-to-site VPN tunnels, each serving different network setup needs. Site-to-site connects whole networks to each other, while remote access allows individual users to connect to a network remotely.

What is a requirement of a site-to-site VPN? ›

To create an internet-based site-to-site VPN, you make a tunnel that connects two networks, for which you need three components: A base network in one location. A satellite network in another location. A tunnel with security gateways on each end.

Which IPsec mode is used for a site to site VPN? ›

Tunnel mode is typically used for site-to-site VPNs where we need to encapsulate the original IP packet since these are mostly private IP addresses and can't be routed on the Internet. I will explain these two modes in detail later in this lesson.

What is full tunnel site to site VPN? ›

A full tunnel VPN is a virtual private network (VPN) configuration that directs all your internet traffic through a VPN tunnel. This means that the VPN connection protects all the data you send and receive. Typically, VPN services offer full tunneling as a standard VPN setup.

What is an example of a site to site VPN? ›

For example, a site-to-site VPN would allow a company's headquarters in Lake Forest, IL to connect to a smaller branch in Los Angeles, CA. Due to the rise of remote work and eLearning, businesses take advantage of this tech to share information securely.

How to configure IPsec tunnels? ›

Set Up an IPSec Tunnel (Tunnel Mode)
  1. Create a Security Policy Rule.
  2. Track Rules Within a Rulebase.
  3. Enforce Security Rule Description, Tag, and Audit Comment.
  4. Move or Clone a Security Rule or Object to a Different Virtual System.
  5. Test Security Rules.

Is IPsec better than OpenVPN? ›

IPsec is typically faster. IPsec also benefits from its integration into the operating system's kernel, allowing for efficient packet processing and less overhead. OpenVPN is slightly slower because of double encryption, but it still offers adequate performance for most enterprise applications.

What is IPsec remote access and site to site VPN? ›

In site to site VPN, IPsec security method is used to create an encrypted tunnel from one customer network to remote site of the customer. In remote access VPN, Individual users are connected to the private network. Site to site VPN does not need setup on each client.

How do I setup an IPsec VPN server? ›

Follow these steps:
  1. Go to Settings > Network > VPN. ...
  2. Select Layer 2 Tunneling Protocol (L2TP).
  3. Enter anything you like in the Name field.
  4. Enter Your VPN Server IP for the Gateway.
  5. Enter Your VPN Username for the User name.
  6. Right-click the ? in the Password field and select Store the password only for this user.
Aug 26, 2021

What ports are required for IPsec site to site VPN? ›

IPSec VPN is a layer 3 protocol that communicates over IP protocol 50, Encapsulating Security Payload (ESP). It might also require UDP port 500 for Internet Key Exchange (IKE) to manage encryption keys, and UDP port 4500 for IPSec NAT-Traversal (NAT-T).

How to configure site to site IKEv2 IPsec VPN using pre shared key authentication? ›

Add an IPsec connection
  1. Go to Site-to-site VPN > IPsec and click Add.
  2. Enter a name.
  3. Select IPv4.
  4. Select Create firewall rule.
  5. Set Connection type to Site-to-site.
  6. Set Gateway type to Respond only. ...
  7. Set Profile to Head office (IKEv2). ...
  8. Set Authentication type to Preshared key.
Jul 25, 2024

Top Articles
How Much Down Payment Do You Need on a House?
Les meilleurs brokers & courtiers en bourse : Comparatif [current_year]
Okatee River Farms
Cvs Devoted Catalog
You can put a price tag on the value of a personal finance education: $100,000
Pwc Transparency Report
Little Rock Arkansas Craigslist
Nashville Predators Wiki
Mills and Main Street Tour
Mary Kay Lipstick Conversion Chart PDF Form - FormsPal
Unit 33 Quiz Listening Comprehension
The Exorcist: Believer (2023) Showtimes
/Www.usps.com/International/Passports.htm
Uta Kinesiology Advising
Bible Gateway passage: Revelation 3 - New Living Translation
Menus - Sea Level Oyster Bar - NBPT
Gazette Obituary Colorado Springs
Disputes over ESPN, Disney and DirecTV go to the heart of TV's existential problems
Craigslist Panama City Beach Fl Pets
Kitchen Exhaust Cleaning Companies Clearwater
Divide Fusion Stretch Hoodie Daunenjacke für Herren | oliv
4.231 Rounded To The Nearest Hundred
Frank Vascellaro
Free Tiktok Likes Compara Smm
Basil Martusevich
Rund um die SIM-Karte | ALDI TALK
The Ultimate Guide to Obtaining Bark in Conan Exiles: Tips and Tricks for the Best Results
Shaman's Path Puzzle
Ark Unlock All Skins Command
Selfservice Bright Lending
Chs.mywork
In Polen und Tschechien droht Hochwasser - Brandenburg beobachtet Lage
Babylon 2022 Showtimes Near Cinemark Downey And Xd
Elgin Il Building Department
20+ Best Things To Do In Oceanside California
Delaware judge sets Twitter, Elon Musk trial for October
Ise-Vm-K9 Eol
Why I’m Joining Flipboard
Mid America Clinical Labs Appointments
Seven Rotten Tomatoes
Sound Of Freedom Showtimes Near Lewisburg Cinema 8
Tgirls Philly
R: Getting Help with R
How To Customise Mii QR Codes in Tomodachi Life?
Conan Exiles Tiger Cub Best Food
Air Sculpt Houston
Clock Batteries Perhaps Crossword Clue
Here’s What Goes on at a Gentlemen’s Club – Crafternoon Cabaret Club
Treatise On Jewelcrafting
Inside the Bestselling Medical Mystery 'Hidden Valley Road'
Bloons Tower Defense 1 Unblocked
Booked On The Bayou Houma 2023
Latest Posts
Article information

Author: Chrissy Homenick

Last Updated:

Views: 5791

Rating: 4.3 / 5 (74 voted)

Reviews: 89% of readers found this page helpful

Author information

Name: Chrissy Homenick

Birthday: 2001-10-22

Address: 611 Kuhn Oval, Feltonbury, NY 02783-3818

Phone: +96619177651654

Job: Mining Representative

Hobby: amateur radio, Sculling, Knife making, Gardening, Watching movies, Gunsmithing, Video gaming

Introduction: My name is Chrissy Homenick, I am a tender, funny, determined, tender, glorious, fancy, enthusiastic person who loves writing and wants to share my knowledge and understanding with you.