Configuring RIP and OSPF Advanced Routing Services (2024)

•

•

•

•

•

•

RIPng – Select one of these modes from the drop-down menu:

•

Disabled (default) – RIP is disabled on this interface

•

Enable – The RIP router on this interface sends updates and process received updates.

•

Passive – The RIP router on this interface does not process received updates, and only sends updates to neighboring RIP routers specified with the CLI neighbor command.

•

Send and Receive – The RIP router on this interface sends updates and processes received updates.

•

Send Only – The RIP router on this interface only sends updates and does not process received updates. This is similar to the basic routing implementation.

•

Receive Only – The RIP router on this interface only processes received updates.

•

Split Horizon – Enabling Split Horizon suppresses the inclusion of routes sent in updates to routers from which they were learned. This is a common RIP mechanism for preventing routing loops. See Maximum Hops . This option is selected by default.

•

Poisoned Reverse – Poison reverse is an optional mode of Split Horizon operation. Rather than suppressing the inclusion of learned routes, the routes are sent with a metric of infinity (16) thus indicating that they are unreachable. See Maximum Hops . This option is selected by default.

•

Receive (available in Send and Receive and Receive Only modes)

•

RIPv1 – Receive only broadcast RIPv1 packets.

•

RIPv2 – Receive only multicast RIPv2 packets. RIPv2 packets are sent by multicast, although some implementations of RIP routers (including basic routing on SonicWALL devices) have the ability to send RIPv2 in either broadcast or multicast formats.

•

Send (available in Send and Receive and Send Only modes)

•

RIPv1 – Send broadcast RIPv1 packets.

•

•

RIPv2 – Send multicast RIPv2 packets.

•

Default Metric – Used to specify the metric that will be used when redistributing routes from other (Default, Static, Connected, OSPF, or VPN) routing information sources. The default value (undefined) is 1 and the maximum is 15.

•

Originate Default Route – This checkbox enables or disables the advertising of the firewall’s default route into the RIP system.

•

Redistribute Static Routes – Enables or disables the advertising of static (Policy Based Routing) routes into the RIP system. The metric can be explicitly set for this redistribution, or it can use the value (default) specified in the Default Metric setting.

•

Redistribute Connected Networks - Enables or disables the advertising of locally connected networks into the RIP system. The metric can be explicitly set for this redistribution, or it can use the value (default) specified in the Default Metric setting.

•

Redistribute OSPF Routes - Enables or disables the advertising of routes learned via OSPF into the RIP system. The metric can be explicitly set for this redistribution, or it can use the value (default) specified in the Default Metric setting.

•

Redistribute Remote VPN Networks - Enables or disables the advertising of static (Policy Based Routing) routes into the RIP system. The metric can be explicitly set for this redistribution, or it can use the value (default) specified in the Default Metric setting.

•

Use Password – Enables the use of a plain-text password on this interface, up to 16 alpha-numeric characters long, for identification.

•

Administrative Distance – The administrative distance value is used by routers in selecting a path when there is more than one route to a destination, with the smaller distance being preferred. The default value is 120, minimum is 1, and maximum is 255.

•

•

•

OSPFv3 – Select one of these settings from the drop-down menu:

•

Disable (default) – OSPF Router is disabled on this interface

•

Enable – OSPF Router is enabled on this interface

•

Passive – The OSPF router is enabled on this interface, but only advertises connected networks using type 1 LSA’s (Router Link Advertisem*nts) into the local area. This is different from the Redistribute Connected Networks options, which would cause the OSPF router to behave as an ASBR, and to use type 5 LSA’s (AS External Link Advertisem*nt) to flood the advertisem*nts into all non-stub areas. For more information, see OSPF Terms .

•

Dead Interval (1-65535) – The period, in seconds, after which an entry in the LSDB is removed if Hello is not received. The default is 40 seconds, with a minimum of 1 and a maximum on 65,535.

•

Hello Interval (1-65535) – The period of time between Hello packets. The default is 10 seconds, with a minimum of 1 and a maximum on 65,535.

•

Router Priority (0-255) – The router priority value is used in determining the Designated Router (DR) for a segment. The higher the value, the higher the priority. For a priority tie, the Router ID acts as the tie-breaker. Setting a value of 0 makes the OSPF router on this interface ineligible for DR status. The default value is 1, and the maximum value is 255.

•

OSPFv3 Area – The OSPF Area can be represented in either IP or decimal notation. For example, you may represent the area connected to X4:100 as either 100.100.100.100 or 1684300900. The default is 0.

•

•

Normal (default) – Receives and sends all applicable LSA types.

•

Stub Area – Does not receive type 5 LSA’s (AS External Link Advertisem*nts).

•

•

•

•

Interface Cost (1-65535) – Specifies the overhead of sending packets across this interface. The default value is 10, generally used to indicate an Ethernet interface. The minimum and default value is 1 (for example, Fast Ethernet) and the maximum value is 65,535 (for example, pudding).

•

Auto – Selecting Auto dims the Interface Cost field as the cost is determined automatically. This checkbox is not selected by default.

•

Instance-ID: (0-255) – The minimum value is 0, the default value is 0, and the maximum is 255. This field is normally dimmed.

•

Authentication - Be sure this setting agrees with the other OSPF routers on the segment for successful neighbor establishment.

•

Disabled – No authentication is used on this interface.

•

Simple Password – A plain-text password is used for identification purposes by the OSPF router on this interface.

•

Message Digest – An MD5 hash is used to securely identify the OSPF router on this interface.

•

Password – Enter the password for this router.

•

OSPFv3 Router ID (n.n.n.n) – The Router ID can be any value, represented in IP address notation. It is unrelated to the any of the IP addresses on the firewall, and can be set to any unique value within your OSPF network.

•

ABR Type – Allows for the specification of the topology with which this OSPF router will be participating, for the sake of compatibility. The options are:

•

Standard – Full RFC2328 compliant ABR OSPF operation.

•

Cisco – For interoperating with Cisco’s ABR behavior, which expects the backbone to be configured and active before setting the ABR flag.

•

IBM – For interoperating with IBM’s ABR behavior, which expects the backbone to be configured before settings the ABR flag.

•

Shortcut – A shortcut area enables traffic to go through the non-backbone area with a lower metric whether or not the ABR router is attached to area 0.

•

Default Metric (1-16777214) – Specifies the metric used when redistributing routes from other (Default, Static, Connected, RIP, or VPN) routing information sources. The default value (Undefined) is 1, and the maximum is 16,777,214.

•

•

Redistribute Static Routes – Enables or disables the advertising of static (Policy Based Routing) routes into the OSPF system. This option is not selected by default.

•

Redistribute Connected Networks - Enables or disables the advertising of locally connected networks into the OSPF system. This option is not selected by default.

•

Redistribute RIP Routes - Enables or disables the advertising of routes learned via RIP into the OSPF system. This option is not selected by default.

•

Originate Default Route – Controls the advertising of the firewall’s default route into the OSPF system on this interface. The options are:

•

Never – Disables advertisem*nt of the default route into the OSPF system.

•

When WAN is up – Advertises the default route into the OSPF system when the WAN is online. The default route is always advertised as an External Type 2 using LSA Type 5.

•

Always – Enables advertisem*nt of the default route into the OSPF system. The default route is always advertised as an External Type 2 using LSA Type 5.

•

Metric (1-16777214) – Can be explicitly set for this redistribution, or it can use the value specified in the Default Metric option. The minimum value is 1, the maximum value is 16,777,214, and the default value is 10.

•

Redistribute Remote VPN Networks - Enables or disables the advertising of static (Policy Based Routing) routes into the RIP system.

•

IP Address Borrowed From - The interface whose IP address is used as the source IP address for the Tunnel Interface.

•

Remote IP Address - The IP address of the remote peer to which the Tunnel Interface is connected. In the case of a SonicWALL-to-SonicWALL configuration with another Tunnel Interface, this should be the IP address of the borrowed interface of the Tunnel Interface on the remote peer.

•

•

•

•

•

•