Raw partitions are supported only when upgrading an existing installation using the configured partitions. On new installations, using raw partitions is not supported by ASMCA or OUI, but is supported by the software if you perform manual configuration
To determine if automatic mounting of new volumes is enabled, use the following commands:
C:\> diskpart DISKPART> automount Automatic mounting of new volumes disabled.
To enable automounting:
Enter the following commands at a command prompt:
C:\> diskpartDISKPART> automount enableAutomatic mounting of new volumes enabled.
Type exit to end the diskpart session.
Repeat steps 1 and 2 for each node in the cluster.
Note:
All nodes in the cluster must have automatic mounting enabled to correctly install Oracle RAC and Oracle Clusterware. Oracle recommends that you enable automatic mounting before creating any logical partitions for use by the database or Oracle ASM.
You must restart each node after enabling disk automounting.
After disk automounting is enabled and the node is restarted, automatic mounting remains active until it is disabled.
As an expert in system administration, particularly in the realm of database management systems like Oracle, I can provide comprehensive insights into the automount feature and its significance within Oracle ASM (Automatic Storage Management) and Oracle Clusterware setups.
The automount feature in Windows is crucial for seamlessly mounting new volumes, ensuring they're accessible for use by various applications and services. This feature might seem to be enabled by default, but it's imperative to verify its status, especially in scenarios where specific configurations are required, as in the case of Oracle ASM and Oracle Clusterware.
In the context of Oracle ASM, utilizing raw partitions or logical drives necessitates the correct configuration of automounting. This configuration ensures that the database can effectively access and utilize these storage resources.
Regarding the evidence to support my expertise in this area, I can discuss the process outlined in your provided article. The article describes the steps to check whether automounting of new volumes is enabled on Windows using the diskpart utility. If the automount feature is disabled, the instructions clearly indicate how to enable it through the command prompt.
Moreover, the note in the article underscores the significance of automounting for Oracle RAC (Real Application Clusters) and Oracle Clusterware. It emphasizes that all nodes within the cluster must have automatic mounting enabled for a correct installation. It also recommends enabling automounting before creating logical partitions for the database or Oracle ASM, further highlighting its critical role in the setup process.
The specific commands provided (diskpart commands) are authentic and align with Windows disk management practices, particularly when dealing with the automount feature. Enabling automounting and restarting each node after the change ensures its persistence until explicitly disabled.
In summary, my expertise aligns with the subject matter presented in the article, showcasing an understanding of Windows disk management (diskpart commands) and its relevance within Oracle ASM and Oracle Clusterware environments, especially concerning the crucial role of automounting for seamless storage access and utilization.
Enable Automount using DiskPart > automount Command
1 Open an elevated command prompt. 3 Type automount enable into the elevated command prompt, and press Enter . 4 Close the elevated command prompt. 5 Restart the computer to apply.
Enable Automount using DiskPart > automount Command
1 Open an elevated command prompt. 3 Type automount enable into the elevated command prompt, and press Enter . 4 Close the elevated command prompt. 5 Restart the computer to apply.
First, you can check if the automount feature is enabled or disabled currently. Press Win + R keys on the keyboard to open Run box.Then type diskpart in the box to open it.In the pop-up window, type automount and press Enter key to execute the command.
Disable the "Automatically mount new volumes" option in Disk Management (Windows): Open Disk Management (right-click on the Start button and select Disk Management). Right-click on the USB drive and select "Change Drive Letter and Paths". Select the drive letter and click on "Remove".
Click the Windows key, enter Task Scheduler. Double-click the Task Scheduler Library on the left, and click Create Basic Task on the right. Name it Mount Virtual Hard Disk. Click Next, click Trigger, start the computer at startup, then click Next again.
RSAT for Windows 10, version 1809 or later versions
To enable the tools, select Start > Settings > Apps (if you're using Windows 10, version 22H2 or later versions, select System instead), and then select Optional features. After that, select the Add a feature panel and enter Remote in the search bar.
To check activation status in Windows 10, select the Start button, and then select Settings > Update & Security and then select Activation . Your activation status will be listed next to Activation.
This command displays information about the file system type, the device on which it is mounted, and the options used during the mount process. The command mountpoint -T /mnt/data displays information on the mount point at /mnt/data.
The findmnt command can be used to display information about a specific mount point or list all the mounted file systems. It also accepts options such as -T to check a specific mount point, -l to list all the mounted file systems and -t to filter the output by file system type.
When you type these diskpart commands, you avoid to assign drive letter to new volumes (automount) and you flush all the old and unused volumes (scrub). You can see that it doesn't remove your actual HD drives, so, by using in a certain way, you can get a chance to still assign letters to your USB drives.
The ISO mount can be launched by right-clicking on the ISO file and using the 'Mount' command. The ISO mount can be launched by right-clicking on the ISO file and using the 'Mount' command. Step 3: To terminate the ISO mount, right-click the virtual drive in Windows Explorer and click 'Eject'.
Choose the apps that will run when you start your device
Go to Start > Settings > Apps > Startup. For any app in the list, select the toggle to set it to On. If you want to change the advanced settings for that app, select the arrow and make changes as desired.
Introduction: My name is Kimberely Baumbach CPA, I am a gorgeous, bright, charming, encouraging, zealous, lively, good person who loves writing and wants to share my knowledge and understanding with you.
We notice you're using an ad blocker
Without advertising income, we can't keep making this site awesome for you.
