Fixed: Cloned Hard Drive or SSD Won’t Boot (2024)

Table of Contents

Why my cloned hard drive or SSD won't boot?

Have you ever been annoyed that your cloned hard drive won’t boot? When you try to upgrade your hard drive to a new HDD or SSD without reinstalling Windows and all the previously installed programs, you’d prefer to clone hard drive. After that, you can boot from the cloned hard drive directly without reinstalling everything from scratch.

However, unfortunately, you may meet the problem that the cloned HDD or SSD won’t boot:

1. The SSD is connected to the PC as an external disk.
2. The cloned SSDis not marked as the start disk.
3. The SSD is incompatible with the BIOS launch mode.
4. The process of copying the disk was either interrupted or corrupted from the beginning.
5. Boot partitions, boot components, or incomplete clones that are missing from the system.

Firstly, if the SSD is linked to the computer as an external drive, you can refer to the following fixes to solve the issue. Next, confirm that the cloned SSD has been appropriately designated as the primary boot disk. It's important to also check for compatibility issues between the BIOS boot mode and the SSD.

In cases where the disk cloning procedure was compromised or prematurely halted, take steps to rectify this potential cause. Instances of incomplete clones, absent boot partitions, or missing boot components should be addressed comprehensively. Additionally, verify the condition of the source disk, ensuring it is bootable. If required, make sure the SSD is equipped with the necessary drivers.

How to fix a cloned drive won't boot

Here we provide two ways to make cloned drive bootable in two different situations. You can choose the appropriate solution based on your own situation.

Situation 1: clone one hard drive to another on the same computer
Situation 2: clone disk from one computer to another

Situation 1: clone one hard drive to another on the same computer

If you are cloning a hard drive to another hard drive on the same computer, but the cloned hard drive won’t boot later, you can try the following ways to make the cloned drive bootable:

▶ 1. Check the boot order

Situation 2: clone disk from one computer to another

If the cloned drive won't boot after you clone disk from one computer to another different one, apart from using the 2 methods in the first situation: check the starup settings and use the bootrec.exe tool to fix MBR or BCD settings, you can also try the following another two solutions.

▶ 1.Check the connection mode

If the original computer uses IDE mode, the destination computer has to use IDE mode. If the source is AHCI, then the target AHCI mode.

▶ 2.Use Dissimilar Hardware Restore

Back up the source HDD onto an external storage device using AOMEI Backupper. Then create an AOMEI bootable media to boot the target computer and restore the backup to the destination HDD with Universal Restore option enabled.

Usually, Bootrec.exe tool can fix the cloned hard drive won’t boot problem, but when you install the cloned drive to another computer with dissimilar hardware, the bootrec.exe tool may not be able to enough because the different hardware requires different drivers. In this case, you can use AOMEI Universal Restore.

Bonus tips:Preventing SSD failure to boot after cloned

In an effort to preserve your time and prevent the recurrence of the situation where the cloned drive fails to launch, we have assembled a list of practical advice. These recommendations are also applicable when transferring the operating system to a new hard drive in Windows 11/10/8/7 through disk cloning.

1.Utilize a reputable cloning software to replicate your system onto a new hard drive or SSD.
2.Using AOMEI Partition Assistantto ensure that the partition types of the source system disk and the target disk are identical, either MBR or GPT. Additionally, ensure that the appropriate boot configuration is selected, either Legacy BIOS (MBR) or UEFI (GPT).
3. Ensure that all system partitions are cloned in order for Windows to function properly.
4.Guarantee that the cloned device is on the boot order.
5. Connect the SSD to your PC using the appropriate cable (IDE/SATA/M.2/PCIe) rather than a USB cable.

FAQd aboutcloned hard drive won’t boot

1. Does cloning an SSD make it bootable?

Yes, cloning a systemSSD can make it bootable.When you clone an SSD, you create an exact copy of the source drive, including the operating system, files, and partitions. If the source SSD was already bootable, the cloned SSD should also be bootable, assuming the cloning process was successful and no errors occurred.

2. Is cloning bad for SSD?

To begin with, cloning is not always a terrible thing. In most circ*mstances, it is highly advantageous and convenient. However, keep in mind that cloning creates an identical clone of your system, and if your existing system installation has defects, you will find the same issues when switching to a new disk.

3. How to check if cloned SSD is bootable?

The most effective method of verifying the success of the cloning is to remove the old HDD and leave the SSD plugged in, and then observe whether it boots. If it does, you may reconnect the HDD and verify that the system continues to launch from the SSD. Subsequently, you may proceed with the deletion of the obsolete partitions.

4.What to do after cloning SSD?

Verify that all data on the SSD has been accurately cloned. If you intend to utilize the original hard drive as storage, it is necessary to format and repartition it. Ensure that the cloned SSD is booting from the BIOS/UEFI of your computer, or you will be unable to activate it from the SSD.