This method applies to all Antminers.
To power off/shut down a miner:
Since the mineris directly connected to the power supply, there is no hard switch on the miner. You only need to pull the power plug (pulling the plug, not the power cable) to disconnect the power.
To restart/reboot a miner:
There are two ways to restart the miner.The first is to power off the miner and then turn it on.The second is to click "restart" on the interface of the miner, as shown in the figure below:
Miner Background> System> Restart
If you still cannot resolve this issue, please get in touch with us for further assistance.
FAQs
Since the miner is directly connected to the power supply, there is no hard switch on the miner. You only need to pull the power plug (pulling the plug, not the power cable) to disconnect the power.
How do I reset a miner? ›
Power off the miner, then hold down the IP Reporter and don't release it. At the same time, power on the mine again. Releasing the IP Reporter after 5 seconds, the machine will automatically restore factory settings.
How do you reset the Bitcoin miner? ›
Method 1: Restore via the “Reset” Button
- Power On: Ensure your miner is turned on and operational.
- Locate the Reset Button: Find the “Reset” button on your miner. ...
- Press and Hold: Press and hold the “Reset” button for about 5 seconds.
Check the control board, and then check the hash board.
If the mining rig still cannot be turned on, it means that the control board is faulty and the control board needs to be replaced.
How do I reset my Antminer d3? ›
The content of this article is suitable for all Antminer. This method can be applied within 10 minutes of starting the miner. After the miner is turned on for 2 minutes, please press and hold the "Reset" button for 5 seconds, and then release it.
How do I turn off miner? ›
Since the miner is directly connected to the power supply, there is no hard switch on the miner. You only need to pull the power plug (pulling the plug, not the power cable) to disconnect the power.
How do you restart a mine in idle miner? ›
Prestige will reset the mine you activate it in, so you have to rebuild the whole mine from scratch. Using Prestige in a mine costs a certain amount of Cash and will add an income multiplier to your mine, so you will make lots more Cash while you rebuild!
How do I know if my Bitcoin miner is running? ›
The common symptoms alarming the possible crypto-mining malware infection threat are the following:
- High CPU usage.
- Slow performance, lagging.
- Overheating.
- Increased internet traffic.
Bitcoin mining typically uses powerful, single-purpose computers that can cost hundreds or thousands dollars. But Bitcoin as we know it could not exist without mining. Bitcoin mining is the key component of Bitcoin's “proof-of-work” protocol.
What is the great reset Bitcoin? ›
The Great Reset and the Rise of Bitcoin is a documentary that explores the current state of our economy and the impact a new monetary system like Bitcoin can have on the world.
An inactive state happens when the system is online and the mining client is mining, but there is no speed (i.e, speed is 0 H/s). Such an event can happen because of the wrongly configured pool, wrong authentication on the pool, wrong port, or a hardware error in ASIC.
How to start a Bitcoin miner? ›
Because it's so popular and there are so many miners competing to earn rewards, it's extremely difficult to make a profit with Bitcoin mining.
- Buy your mining equipment. ...
- Set up a crypto wallet. ...
- Configure your mining device. ...
- Join a mining pool.
Worker is mining
If worker has a hashrate it means something is happening. If the hashrate is 0 H/s, then your worker is not mining and there is an error in your mining client that you need to resolve.
How do I clear my bitcoin miner? ›
How to Delete a Miner Virus
- Step 1: start the system in Safe Mode. Restart your PC. ...
- Step 2: run antivirus software. Make sure that you have legit antivirus software installed. ...
- Step 3: restart your device.
- Step 4: Don't forget to update the OS and software. Check for system updates.
Reset the miner (press the “RESET" button over 3 second, until red-green light flickering).
How do I start the missing miner? ›
Start this quest by interacting with the "Work Handbook" inside a tree log in the Underground Waterway.
- Collect "mushroom meat" together with Uncle He.
- Defeat the Floating Fungi.
- Bring Uncle He back to camp to meet Jinwu.
