To build an infrastructure or facility, youâll most likely require steel beams, like I-beams and wide flange beams. While these are common types of steel beams, they often get confused with one another. Understanding their distinctions begins with understanding the terms flange and web. Flanges are the beamâs horizontal components, while webs are the vertical components that connect the flanges.
Here weâll review the differences and similarities between I-beams vs. W-beams, as well as how to select the right beam for your application.
Sometimes called a W-beam, a wide flange beam is a type of steel beam shaped like a sideways H. The web can be of equal width or wider than the flange. The size of a W-beam is identified by the first number in the product description followed by the weight per foot. For example, a W21x44 beam measures about 21 inches in width and 44 pounds per foot. The web bears shear forces while the flange resists bending forces.
Many construction projects rely on wide flange beams, including:
Bridges
Factory platforms
Support beams for steel buildings and factories
Machinery
Truck bed frames
I-beams tend to have flanges that are shorter than the web, resulting in a cross-section shaped like a capital âI.â This design enables the beam to bend when high pressure is applied. W-beams offer more variety in sizes and lengths, whereas I-beams have a more limited selection.
Support beams for facilities, construction, and engineering
Support steel angles and channels
Both wide flange beams and I-beams are reliable weight-bearing components for many applications. However, the best type will depend on your projectâs specific requirements.Â
Wide Flange Beams
Compared to I-beams, wide flange beams have a wider flange and thicker web. Their design enables them to handle more weight, and theyâre suitable for spans of up to 300 feet. Wide flange beams also feature a bevel that connects the web and top and bottom flanges. Lightweight wide flange beamsârather than I-beamsâare typically used in residential construction projects.
Infra-Metals stocks W-beams from W4x13 to W44x335, with lengths up to 70 feet.
I-Beams
I-beams feature thinner webs and tapered flanges for a more lightweight construction. The I-beamâs shorter length makes it compatible with spans between 33 and 100 feet. Where wide flange beams come in three connected metal components, I-beam steel comes in a single metal piece.
Infra-Metals carries I-beams from S3x5.7 to S24x121, with various lengths up to 60 feet.
I-beams and wide flange beams are vital construction elements in many types of structures. Now that you know the difference between wide flange beams vs. I-beams, you can select the best beam for your application depending on your engineering specifications.
Since 1990, Infra-Metals has been a premier provider of top-quality structural steel beams. In addition to I-beams and wide flange beams, we carry a selection of angles, tubes, plates, channels, solar panel mounts, and more. We also offer a variety of processing services, including drilling, cutting, blasting, and cambering.Â
All of our steel products for U.S. applications feature standard alloys specified by ASTM International (American Society for Testing and Materials). Infra-Metals is also a proud member of the Reliance Steel & Aluminum Co. family. We aim to serve as your one-stop shop for steel construction materials and processing.
Browse our catalog to view more of our offerings and capabilities, orrequest a quote at any time to get started on selecting the right solution for your application.
Compared to I-beams, wide flange beams have a wider flange and thicker web. Their design enables them to handle more weight, and they're suitable for spans of up to 300 feet. Wide flange beams also feature a bevel that connects the web and top and bottom flanges.
An I-beam has tapered flanges with a narrower flange than most wide flange beams, making it a lighter building material. A wide flange beam, with wider flanges and web than the I-beam, can handle more weight, but this makes it heavier overall.
To short, the main difference between an H-beam and an I-beam is that the web of an H-beam is much thicker than that of an I-beam. A thicker web means a stronger beam, which allows for more load-bearing capacity. This means that for the same amount of structural support, you can use fewer H beams than I beams.
You get many benefits when using wide flange beams for structural projects. Since wide flange beams are produced to be equal in width and depth, it's better oriented vertically to carry an extremely heavy load in a construction project, making it suitable for multi-story construction projects.
Because an i-beam is rolled into that “I” shape, the i-beam will have more flange surface area than a solid beam. For the same amount of steel used and the same overall weight, you'll get a higher load-bearing capacity and a high moment of inertia with an i-beam because of its ability to redistribute that weight.
They're frequently used as reinforcements in bridges, commercial buildings, and residential structures and can be fabricated from wood, aluminum, steel, or composite materials.
Overall, the title of “Stronger Beam” goes to H-beams. An H-beam's durability comes from its strength-to-weight ratio in the cross-section. This optimized design means that these beam types have more strength against heavier loads.
I beams are resistant to aging and are easily adaptable to structural additions and modifications due to their composition. I beams are always in demand because of their strength, cost effectiveness, and versatility.
H-beams may appear like the obvious choice – they're cheaper, have a greater capacity to withstand loads and are more resistant to bending. However, I-beams are lighter, easier to work with and have high tensile strength. This makes them ideal to handle direct pressure, and are used for steel framed buildings.
H-Beams. One of the strongest steel beams on the list, H-beams, is made up of horizontal elements, while the vertical beams act as the web. The flanges and web create a cross-section that mimics the shape of the letter “H” and are popular in construction or civil engineering projects.
Making wide flange beams is economical, and takes less construction time. Combine that with their improved weight resistance and distribution, this type of beam is a highly efficient part. When it comes to the materials used to make these types of beams, they also provide significant cost-efficiency.
Disadvantages: The slip on plate flange has poor rigidity, so it should not be used in chemical process piping systems with requirements of supply and demand, flammability, explosion and higher vacuum degree. Advantages: It is convenient to install on site.
Summary: The I-beam section has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. H steel is the opposite, so both have their own advantages and disadvantages.
I-section in comparison to any other provides higher section modulus and thus providing better lateral stability as compare to other sections. ∴ The rolled steel I – sections are most commonly used as beams because these provide a large moment of inertia with the less cross-sectional area and greater lateral stability.
I-beams tend to have flanges that are shorter than the web, resulting in a cross-section shaped like a capital “I.” This design enables the beam to bend when high pressure is applied. W-beams offer more variety in sizes and lengths, whereas I-beams have a more limited selection.
The similarities between an HP beam (half-power beamwidth) and a wide-flange beam primarily lie in their structural design, while the context of HP beam in the given information seems to refer to an antenna characteristic.
The shape of the I-beam level gives it a strength that a straight level wouldn't have. It prevents the spirit level from twisting out of shape and reduces the stresses of impact on the profile. However, as it is a lighter level it will not have the same strength and robustness as a box level.
Address: Apt. 171 8116 Bailey Via, Roberthaven, GA 58289
Phone: +2585395768220
Job: Lead Liaison
Hobby: Lockpicking, LARPing, Lego building, Lapidary, Macrame, Book restoration, Bodybuilding
Introduction: My name is Sen. Ignacio Ratke, I am a adventurous, zealous, outstanding, agreeable, precious, excited, gifted person who loves writing and wants to share my knowledge and understanding with you.
We notice you're using an ad blocker
Without advertising income, we can't keep making this site awesome for you.